PEL102 Power and Energy Data Logger
- Power (VA, W, var) & Energy (VAh, Wh, varh) Measurements on 50/60Hz, 400Hz and DC Systems
- Measurement Range of 100mA to 10,000 Amps with MiniFlex Current Sensors (Included)
- Store Measured Current and Voltage Readings onto SD(HC) Cards up to 32 GB
- RMS and DC Measurements of each Phase at 128 Samples per Cycle
- Bluetooth, USB and Ethernet LAN Communications Options for Setup and Configuration
- New! Android App to Connect, Configure, Setup, View Data Using Bluetooth or WiFi Communications
Includes Tool Bag, (3) MiniFlex Current Sensors, USB Cable, (4) Black Test Leads w/ Alligator Clips, AC Power Adapter, (12) Color-Coded ID Markers, Multifix Mounting System, Safety Card, 2 GB SD Card and USB-SD Card Reader, USB Memory Stick with User Manual and DataView PC Software
Overview of the AEMC PEL102 Power & Energy Data Logger
The PEL102 is an economically priced, simple to use, single, two, and three phase power/energy data logger. All PEL 100 series loggers offer a full range of essential functions for recording power and energy data from most electrical power networks in use across the world today. The PEL 100 series devices measure and record three True RMS voltage inputs and current inputs, Watts, VARS, VA, and Energy (kWh & kVA). Additionally, Power Factor (PF), Displacement Power Factor (DPF), Crest Factor, Frequency, and Total Harmonic Distortion (THD) are calculated and recorded as well. Individual harmonic percent information from 1 to the 50th harmonic is recorded at the operator’s choice. All variables are recorded and stored at a once second interval and on user selectable demand intervals ranging from 1 to 60 minutes. The PEL 100 series loggers are powered using rechargeable batteries or can be powered directly off the panel when used with the optional 2137.98 power adaptor (sold separately). The PEL 100 series is the perfect choice for electricians, engineers, and contractors performing building and system monitoring and energy audits. The compact design allows the device to be installed inside a load center panel (including the current sensors) allowing the doors to close on most panels.
The PEL102 includes a storage bag, 3 x MiniFlex MA193-10-BK current sensors, 5’ USB cable, four black test leads and alligator clips, power cord, twelve color-coded ID markers, SD-Card with USB reader, and a USB drive containing the DataView software.
Looking for something similar but with a built-in display? Check out the PEL 103!
AEMC ML912 AC Current Simple Logger Specifications
Number of Channels | 2 Channel |
Input Connection | Captive MiniFlex™ AC current Flexible Sensors |
Measurement Range | Channel 1: 0.5 to 100 Aac Channel 2: 5 to 1000 Aac |
Resolution | 0.1 A |
Accuracy (50/60Hz) |
Channel 1: 0 to 1A Unspecified (1 to 100 A: ±1% of Reading + 0.5A) Channel 2: 0 to 5A Unspecified (5 to 1000A: ±(1% of Reading + 1A) |
Sample Rate | 64 Samples/Cycle |
Storage Modes | Start/Stop, FIFO and Extended Recording Mode (XRM™) |
Storage Rate | Programmable from 125ms to 1 Day |
Recording Length | 15 Minutes to 8 Weeks Programmable Using DataView Software |
Data Storage Capacity | 240,000 Readings/Measurements (Stored in Non-Volatile Memory, Retained If Battery is Low or Removed) |
Communication | USB 2.0 Optically Isolated |
Power Source | (2) 1.5 Volt AA-cell Alkaline Batteries |
Battery Life | 100 Hours to > 45 Days (Dependent on Sample Rate and Recording Length) |
Sensor/Cable Length | Sensor: 6" (152mm) Cable: 6 ft (2 Meters) |
Operating Range | Temperature: 14°F to 122°F (-10°C to 50°C) Humidity: 0 to 85% RH at 95°F (35°C), Non-Condensing Altitude: Up to 2000 Meters |
Storage Range | Temperature: -4°F to 140°F (-20°C to 60°C) Humidity: 0 to 85% RH at 95°F (35°C), Non-Condensing |
Standards Compliance | IP40, EN61326-1; 07/1997 (+A1 10/1998, +A2 09/2001, +A3 05/2004) |
Safety Ratings | EN61010-1; CATIII; 300 Volts CAT IV; Pollution Degree 2 |
Case | UL94-V0 |
Vibration | IEC 68-2-6 (1.5mm, 10 to 55Hz) |
Shock | IEC 68-2-27 (30G) |
Drop | IEC 68-2-32 (1m) |
Software | DataView Software (Included) |
OS Compatibility | Windows 11, 10 and 7 (32 and 64 Bit) |
Dimensions | 4.95" x 2.75" x 1.28" (136mm x 70mm x 32mm) |
Weight | 8.67 oz (245 grams) - with Battery |