HOBO RH/Temp/Light/External Data Logger
Onset 4-Channel Logger for Temperature, Relative Humidity, Light Intensity and 1 Additional External Input
 The HOBO RH/Temp/Light/External data logger measures and logs humidity, temperature, light and has 1 additional external input channel. The logger features a user
selectable sampling interval of 0.5 seconds to 9 hours,
typical battery life of 1 year, programmable
start time/date, and storage of up to 7,943 Samples/Readings without downloading.
Included with Data Logger
>> Mounting Kit (Hook/Loop, Magnet, and Tape)
Required with the Data Logger
>> BoxCar Software Kit
List of Available External Sensors. (Temperature, AC Current, 0-2.5 Volt DC and 4-20 mA)
NOTE: NIST Calibration is available.
Large Quantity Discounts Are Available!
Due to New CE Requirements, this product is No Longer Available for EU Countries, Check out the U12-012 Data Logger As An Alternative.
Features Specifications Compatible External Sensors
| Description |
Part Number |
Qty 1-9 |
Qty 10+ |
|
| HOBO RH/Temp/Light/External, 4 channels |
H08-004-02
|
$160.00 |
$148.00 |
 |
| Software Kits - 1 Required |
| BoxCar Pro 4.3 Software and Serial Cable Kit |
BCP4.3-ON
|
$125.00 |
$118.00 |
|
| BoxCar 3.7 Software and Serial Cable Kit |
BC3.7
|
$55.00 |
$53.00 |
|
| Optional Accessories |
| Extra/Replacement Batteries (pack of 5) - CR2032 Lithium Batteries |
HRB-TEMP-5
|
$10.00 |
$8.00 |
|
| Extra Serial Interface Cable |
Cable-PC-3.5
|
$10.00 |
$9.00 |
|
| Glacier Clear Xtreme Protective Case (3.93" x 2.4" x 0.94") |
T1000.1
|
$9.00 |
call |
|
| Blue Xtreme Protective Case (3.93" x 2.4" x 0.94") |
T1000.4
|
$9.00 |
call |
|
| Keyspan USB 4-Port Serial Adapter |
USA-49WG
|
$149.00 |
call |
|
| Replacement RH Sensor for H8 Indoor Loggers |
HUM-UPS-500
|
$19.00 |
call |
|
| 6 foot M/F RS232 extension cable, DB9 (for providing an extension between interface cable and PC serial port) (Limited Quanitity - 5 Available) |
CABLE-DB9-6--U--
|
$6.00
$4.00 |
call |
|
| Standard NIST Calibration Service |
| Compatible Sensors |
| Onset Air Temperature Sensor |
TMC6-HE
|
$35.00 |
call |
|
| 1ft Air/Water/Soil Temperature Sensor |
TMC1-HD
|
$32.00 |
$30.00 |
|
| 6ft Air/Water/Soil Temperature Sensor |
TMC6-HD
|
$35.00 |
$33.00 |
|
| 20ft Air/Water/Soil Temperature Sensor |
TMC20-HD
|
$40.00 |
$38.00 |
|
| 50ft Air/Water/Soil Temperature Sensor |
TMC50-HD
|
$45.00 |
$43.00 |
|
| Stainless Steel Temperature Probe (4" Probe with 6' Cable) |
TMC6-HC
|
$79.00 |
$73.00 |
|
| Voltage Input Cable |
CABLE-2.5-STEREO
|
$9.00 |
$8.00 |
|
| 4-20 mA Cable |
CABLE-4-20MA
|
$25.00 |
$20.00 |
|
| 0-20 Amp split-core AC Current Sensor |
CTV-A
|
$90.00 |
$84.00 |
|
| 0-50 Amp split-core AC current sensor |
CTV-B
|
$90.00 |
$84.00 |
|
| 0-100 Amp split-core AC current sensor |
CTV-C
|
$90.00 |
$84.00 |
|
| 0-200 Amp split-core AC Current Sensor |
CTV-D
|
$115.00 |
$107.00 |
|
| 0-600 Amp split-core AC Current Sensor |
CTV-E
|
$115.00 |
$107.00 |
|
| Telaire 7001 Carbon Dioxide (CO2) Monitor |
TELAIRE-7001
|
$459.00 |
$449.00 |
|
| Telaire CO2 Monitor to Data Logger Cable |
CABLE-CO2
|
$29.00 |
$27.00 |
|
| AC Voltage Transmitters View Specs |
| conLab AC Voltage Transmitter - 150 VAC |
T-CON-ACT-150
|
$139.00 |
call |
|
| conLab AC Voltage Transmitter - 300 VAC |
T-CON-ACT-300
|
$139.00 |
call |
|
Temperature and External Input Logger Features
- 4 Channel Data Logger with Internal Temperature, Humidity and Light Sensor and External Input
- Internal Temperature Sensor on 4" Wire can Extend from Case
- External Input Accepts Temperature, AC Current, 4-20 mA and 0-2.5 Volts DC Sensors. See List of Compatible External
Sensors
- Readout and Relaunch Logger with Optional HOBO Shuttle
- Programmable Start Time/Date
- Nonvolatile EEPROM Memory Retains Data Even If Battery Fails
- Blinking LED Light Confirms Operation
- Battery Level Indication at Launch
- Requires BoxCar Software Kit for Operation and Data Manipulation
Temperature and External Input Logger Specifications
| Data Storage Capacity |
7,943 8-bit Samples/Readings |
| Sampling Rate |
0.5 Second to 9 Hours (User Selectable) |
| Operating Range |
Temperature: -20°C to 70°C (-4°F to 158°F)
Humidity: 0 to 95% RH non-condensing, non-fogging |
| Operating Modes |
Stop When Full
Wrap-Around When Full |
| Light Intensity |
Range: 2 to 600 footcandles (lumens/ft2)
Accuracy: ±2 footcandles, ±20% of Reading
Angular Response: Roughly Cosine of the Angle From Directly Above Sensor |
| Temperature Sensor |
Range: -4°F to 158°F (-20°C to 70°C)
Range Outside Case: -40°F to 248°F (-40°C to 120°C)
Accuracy: ±1.27°F (±0.7°C) at +70°F
Resolution: 0.7°F (0.4°C) at +70°F
Response Time (Sensor Inside Case): 15 min.
Response Time (Sensor Outside Case): 1 min. |
| Humidity Sensor |
Range: 25% to 95% RH at 80F for Intervals < 10 Sec, Non-Condensing and Non-Fogging
Accuracy: ±5%
Response Time (In Air): 10 min.
Sensor Operating Environment: 5°C to 50°C (41°F to 122°F) , Non-Condensing and Non-Fogging |
| Compatible External Input Types |
Temperature Sensors (#TMCx-Hx)
Split Core CTs for AC Current (#CTV-X)
Voltage Transmitters (#T-CON-ACT-X)
4-20mA Input Cable (#CABLE-4-20mA)
0 to 2.5 Volt DC Input Cable (#CABLE-2-5-STEREO)
Carbon Dioxide for Telaire Monitor (#CABLE-CO2) |
| External 2.5V Input |
2.5 mm Jack: External Input Ground, Input, Switched 2.5 Volt Output; External Input Ground Connection is not the Same as PC Interface Connection Ground and Not Be Connected to Any External Ground
Input Range: 0 to 2.5 Volts DC
Accuracy: ±10 mV ±1% of Reading
Resolution: 10mV (8-bit)
Out Power: 2.5 Volts DC @ 2mA, Active Only During Measurements |
| Drop Proof |
Up to 5 ft. |
| Time Accuracy |
±1 Minute per Week at 20°C (68°F) |
| Storage Range |
Temperature: -40°C to 75°C (-40°F to 167°F) |
| Battery Life |
Typically 1 Year |
| Battery |
3-Volt CR-2032 Lithium Battery (User Replaceable) |
| Standards Compliance |
CE |
| Weight |
29 grams (1 oz) |
| Dimensions |
61mm x 48mm x 20mm (2.4" x 1.9" x 0.8") |
Light Intensity FAQ's
Can I use the light sensor on the H08-004-02 logger as an inexpensive light meter?
No! These light intensity loggers are designed to give you a general comparative idea of how much light there is in an area; sunlight v. shade, lights on/off, etc. If you are planning on recording specific lighting information or absolute values, these loggers will not give you accurate data.
Please note that the light sensor on this logger will record from 2 to 600 lumens per sq/ft. Full sunlight is 10,000 lumens per sq/ft. This sensor is intended for indoor light levels only.
The light sensor on the H08-004-02 measures in lumens/sq foot. How does this measurement relate to Lux and Foot-candles?
The two most popular scales for light measurement are Lux, which is the European scale, and Foot-candles which is the U.S. scale.
Lux and Foot-candles are measure of illumination - the amount of light falling on an object per unit area. The difference is whether the light is measured in square meters or square feet:
1 lumens / sq. meter = 1 lux
1 lumens / sq. foot = 1 foot-candles
How can I convert between lux and Foot-candles?
To convert between lux and foot-candles the following factors can be used:
Lux = 0.0929 * FC
FC = 10.76 * Lux
Other light sensors are available for the HOBO Weather Station Data Logger.
MicroDAQ.com accepts
Visa, MasterCard and American Express
All prices are in U.S. Dollars.
No U.S. sales tax
|
