MicroDAQ.com
Toll Free: 1-877-275-9606
(603) 746-5524
$5.99 Flat Fee Economy Shipping on Most Items Shipped in the Continental USA

You have no items in your shopping cart.

Subtotal: $0.00

Measurement Computing USB-1608G 16 Channel 250k/s High Speed Multifunction USB Data Acquisition Module

  • Measurement Computing USB-1608G 16 Channel 250k/s High Speed Multifunction USB Data Acquisition Module


16 Channel 250 k/s High-Speed Multifunction DAQ Device

Measurement Computing USB-1608G Series Data Acquisition w/ Single-Ended & Differential Analog Inputs

Part Number: USB-1608G

Ask a question (1)

Be the first to review this product


  • (16) Analog Inputs, (8) Independent Digital I/Os, (2) Counter Inputs and (1) Timer

  • 1 S/s to 1MS/s Sampling Rate, Software Programmable

  • Single and Differential Analog Inputs w/ Measurement Range up to ±10 Volts

  • Measurement Rate up to 250 k/S Aggregated Over All Analog Input Channels

  • Powered by 5 Volt USB Supply from Your PC Computer, No External AC Power Required


Includes USB Cable and Measurement Computing DAQ Software Suite (TracerDAQ, InstaCal, Drivers for DASYLab and Universal Library for LabView and Android) Available as a Download

Availability: In stock

$419.00

Measurement Computing USB-1608G 16 Analog Input High Speed USB Data Acquisition DAQ Module Specifications

Analog Input A/D Converter Type: Successive Approximation
ADC Resolution: 16 Bits
Channels*: 8 (Differential); 16 (Single-Ended)
Input Voltage Range*: ±10V; ±5V; ±2V; ±1V per Channel
Input Impedance: 1GΩ (Power On); 820Ω (Power Off)
Input Bias Current: ±10 nA
Input Bandwidth: 750 kHz (All Input Ranges, -3dB Signal)
Input Capacitance: 60 pf
Sampling Rate*: 0.0149 Hz to 250 kHz
Burst Mode**: 4 µs
Throughput: 33 - 4000 S/s (Software); 250 kS/s (Hardware)
* Software Selectable
** Software-Selectable Using the Internal A/D Clock; Always Enabled When using the External Clock (AICKI Command)
Digital I/O Digital Type: CMOS
Number of I/O: 8
Configuration: Each bit Input or Output
Transfer Rate: 33 to 8000 port Reads/Writes or Single Bit Reads/Writes Per Second
Input High Voltage: 2.0 Volts (Min); 5.5 Volts (Max)
Input Low Voltage: 0.8 Volt (Max); -0.5 Volt (Min); 0 Volt Recommended
Output High Voltage: 4.4 V Min (IOH= -50uA); 3.76 Volt Min (IOH= -2.5 mA)
Output Low Voltage: 0.1 V Max (IOL= 50uA); 0.44 Volt Max (IOL= 2.5 mA)
Output Current: ±2.5 mA Max
External Trigger Trigger Source: TRIG input
Trigger Mode: Edge or Level Sensitive, Rising or Falling Edge, High or Low Level
Trigger Latency: 1 µs + 1 clock Cycle Max
Pulse Width: 100 ns Min
Input Type: Schmitt Trigger, 33 Ω Series Resistor and 49.9 kΩ Pull-Down to Ground
Input High Voltage: 2.2 Volt (Min); 5.5 Volt (Max)
Input Low Voltage: 1.5 Volt (Max); -0.5 Volt (Min); 0 Volt (Recommended)
External Clock I/O Input Clock Rate: 250 kHz Max
Clock Pulse Width: 400 ns Min (Input and Output)
Input Type: Schmitt Trigger, 33 Ω Series Resistor and 49.9 kΩ Pull-Down to Ground
Schmitt Trigger Hysteresis: 0.4 Volt to 1.2 Volt
Input High Voltage: 2.2 Volt (Min); 5.5 Volt (Max)
Input Low Voltage: 1.5 Volt (Max); -0.5 Volt (Min); 0 Volt (Recommended)
Output High Voltage: 4.4 V Min (IOH= -50uA); 3.76 Volt Min (IOH= -2.5 mA)
Output Low Voltage: 0.1 V Max (IOL= 50uA); 0.44 Volt Max (IOL= 2.5 mA)
Output Current: ±2.5 mA Max
Counter Channels: 2 (CTR0 and CTR1)
Resolution: 32-bit
Counter Type: Schmitt Trigger, 33 Ω Series Resistor and 49.9 kΩ Pull-Down to Ground
Schmitt Trigger Hysteresis: 0.4 Volt to 1.2 Volt
Input Source: Terminal 52 (CTR0); Terminal 51 (CTR1)
Read/Write Rates*: 33 to 8000 Reads/Wrires per Second
Input High Voltage: 2.2 Volt (Min); 5.5 Volt (Max)
Input Low Voltage: 1.5 Volt (Max); -0.5 Volt (Min)
Input Frequency: 20 MHz Max
High Pulse Width: 25 ns Min (Low and High)
Timer Output Type: PWM Output with Count, Period, Delay and Pulse width Registers
Output Value: Default State is Idle Low with Pulses High, Software-Selectable Output Invert
Internal Clock Frequency: 64 MHz
Register Widths: 32-Bit
Pulse Width: 15.625 ns Min (Low and High)
Output High Voltage: 4.4 Volt Min (IOH @ -50 µA); 3.76 Volt Min (IOH @ -2.5mA)
Output Low Voltage: 0.1 Volt Max (IOL @ 50 µA); 0.44 Volt Max (IOL @ 2.5 mA)
Output Current: ±2.5 mA Maximum
Memory Data FIFO: 4kS (Analog Input); 2 kS (Analog Output)
Non-Volatile: 32 KB (28KB - Firmware; 4KB User Data)
Quiescent Current 230 mA*
* Includes 10 mA for Status LEDs. Doesn't include potential loading of Digital I/O Bits or +5 Volt Terminal
Operating Range Temperature: 0°C to 55°C Max
Humidity: 0% to 90% RH Non-Condensing Max
Storage Range Temperature: -40°C to 85°C Max
Humidity: 0% to 90% RH Non-Condensing Max
Software Compatibility Windows® 7, Vista, XP SP2+ (32-Bit or 64-Bit), Linux® and Mac®
Dimensions 12.7 cm x 8.9 cm x 3.5 cm (5.0" x 3.53" x 1.40")
User Connection Length: 3 Meters (9.84 feet) Max.

Customer Reviews

Write Your Own Review

You're reviewing: 16 Channel 250 k/s High-Speed Multifunction DAQ Device

How do you rate this product? *

  1 star 2 stars 3 stars 4 stars 5 stars
Price
Quality
Value

  • Answer:

    Yes, there is a Linux driver that will work on Ubuntu.

Leave a Reply

  • Reload captcha

Ask Your Question

  • Reload captcha

* Required Fields